Monday, August 5, 2013

Make Some Nautical Knot Bracelets

How-Tuesday: Nautical Knot Bracelets

Etsy.com handmade and vintage goods
cfrenchie
Bring a little seafaring flair to your summer style with these bright, bold bracelets. Inspired by Simone’s sailor’s knot bracelet tutorial, I decided to re-imagine this nautical classic. The project itself is very approachable, so even if you’re not an experienced knotter, you’ll be able to cruise through these steps.
etsy-howto-sailorsknot-bracelet-supplies
You will need:
Cottonparacord or maritime cord
Measuring tape
Lightly colored masking tape
E-600 glue or hot glue gun
Large spring clasp
Embroidery floss
Large needle
Pen (not pictured)
Optional:
Paint brush and acrylic paint
Rhinestone chain
Iron-on studs
Large jump rings (not pictured)

Step 1: Measure and Cut

etsy-howto-sailorsknot-bracelet-1
First, make a measuring cord. This will help you create a bracelet that fits perfectly. Wrap the measuring tape around the bony part of your wrist, making sure the fit is snug but not tight. For a tighter fit, round the measurement to the nearest 1/2 inch. For a looser fit, add an extra inch to your measurement. Cut your cord to this measurement.
etsy-howto-sailorsknot-bracelet-003
Next, set your clasp next to the piece of cut cord, and trim away the total length of the clasp. This will be your measuring cord; set it aside.

Step 2: Create Your Knot

etsy-howto-sailorsknot-bracelet-004
Next, cut 2 pieces of cord measuring at least 22 inches long. Fold one piece of cord in half, and tape the cut ends together using the masking tape. Repeat with the other piece of cord.
etsy-howto-sailorsknot-bracelet-6ab
To create a carrick knot, take one of your long, taped pieces of cord and make a loop with the masking taped end on the underside, pointing upwards. We’ll call the taped end of this loop “a” and the other end of the loop “b.”
etsy-howto-sailorsknot-bracelet-7ab
Take the second piece of looped, taped cord and place it on top of the loop you created. The end with the tape facing upwards will be end “A.” The looped end that faces downwards will be end “B.”
etsy-howto-sailorsknot-bracelet-8ab
Wrap “A” under “a,” and over “b” of the previous loop you created.
etsy-howto-sailorsknot-bracelet-10ab
Next, wrap end “A” under the loop created with your other piece of cord, over end “B,” and back under the loop (photographed above).
etsy-howto-sailorsknot-bracelet-11
Pull on all four ends of your knot to tighten it. If it looks wonky, use your fingers to even out the cord and flatten your knot.

Step 3: The Perfect Fit

etsy-howto-sailorsknot-bracelet-005
To finish your bracelet, you need to bring the ends of the cord together. You’ll want the taped cord ends to be shorter and the looped ends to be longer. Cut both of the taped ends (“a” and “A”) to approximately 1 to 1 ½ inches length from your knot.
etsy-howto-sailorsknot-bracelet-006
Place the measuring cord you made in Step 1 next to your bracelet as a guide, so that the knot aligns with the center of the cord.
etsy-howto-sailorsknot-bracelet-007
Take one of the looped ends and fold it back over itself so that it lines up with the end of your measuring cord. Take the taped end of the bracelet and place it over the folded side. Mark a line where the cords meet.
etsy-howto-sailorsknot-bracelet-016
Unfold the longer, marked cord and apply a thin layer of tape over the marking. Trim at the line and repeat on the other side.
etsy-howto-sailorsknot-bracelet-017
To add your hardware, choose the side you want to have the clasp. Slide the clasp onto the end of the longer piece of cord. Fold that piece back to meet the shorter piece of cord.
etsy-howto-sailorsknot-bracelet-018
Dab glue where the ends meet, holding them down until the bond is made. Cover with masking tape. Repeat this step on the other side, without the clasp to make a loop of cord that the clasp will catch to close the bracelet. If you’d like a larger fit, you can add a jump ring to this side before you glue the cord.
20
To finish the bracelet, cover the masking tape with wrapped embroidery floss. You’ll want to secure the floss with a square knot, hold the tail end against the masking tape and wrap tightly until the tape is covered.
etsy-howto-sailorsknot-bracelet-21-24
Tie off the floss with a knot, then use a needle to hide the tail under the wrapped section. Trim. Repeat these steps on the other side of your bracelet.
28
If you want to take things a step further, you can add embellishments like studs, paint, or rhinestone chain. Get creative!
etsy-howto-sailorsknot-bracelet-large
And there you have it. Your bracelet is all set for a trip to the beach!
bracelet-final
blogpromo_20130523_blue
All photographs by Romain Laurent.
Clare McGibbon is a Brooklyn-based designer and maker. When she's not working on Etsy's international support team, she's dreaming up new DIYs. Keep up with her latest creations on InstagramFacebook and Pinterest.

1 comment: